Size: 2.7 GB,
Eng,
Free
Хакинтош (англ. hackintosh, от слов хакер и макинтош) - это ПК,
собранный любителем и поддерживающий работу с операционной системой Mac
OS, во взломанном для запуска на PC варианте называемой OSx86, т.е.
более дешевый аналог компьютера Apple. Так как современные версии этой
системы рассчитаны на процессор Intel и другие стандартные компоненты,
возникает теоретическая возможность запускать ее на любых ПК. В
реальности, поддерживается только узкий набор аппаратуры, который
встречается в настоящих макинтошах, поэтому "хакинтош" должен состоять
исключительно из таких деталей. Кроме того, коммерчески поставляемая
система защищена от работы на чужой аппаратуре, так что в "хакинтоше"
применяют старую служебную версию без этой защиты, либо взломанную
более свежую версию. В зависимости от точности подбора аппаратуры,
такой компьютер может работать как довольно устойчиво, так и
неприемлемо. Например, типичная конфигурация мощного хакинтоша: ASUS
P5B/Core 2 Duo 2.4 Ghz/2x1024 mb/GeForce 7900GS TOP 256mb/DVD-RW SATA
NEC/HITACHI 320GB SATA.
Системные требования:
Скриншот №1 Скриншот №2
Инсталляция на AMD
Required:
-A computer with an AMD processor
-An untouched Leopard GM disk image
-A copy of OS X Tiger already installed
-A separate partition for Leopard
-A copy of the AMD Decrypts (http://rapidshare.com/files1/files/65593520/9A581_amd.zip.html)
-Shrinker.zip (http://www.mediafire.com/download.php?51y9jfdzxdf)Fixed! Thanks Daniel53!
-A hacked kernel (included)
-Some blank DVD-/+ R’s or a spare 7 gig partition (You’re better off
with the spare partition, or even a DVD RW, trust me, it’s gonna take a
few tries before you get this working.)
-A bit of knowledge and confidence
Disclaimer:
I write this guide based on my experience with my AMD Athlon 3500+.
Depending on your hardware, your millage may vary. Please note that I
am not responsible for your actions. This includes any damage inflicted
upon your computer, yourself, or your family members. I am not to be
held responsible for any legal issues that this may cause you. By
reading this guide you hereby agree to these terms ;). In other words:
DO NOT WANT LAWSUITE KTHX! Before we begin, let me clarify that this
guide is ment to be followed assuming you have a copy of tiger already
installed to do the patching from. This guide will not help you install
leopard by itself, you must have a copy of tiger already installed to
follow this guide. Creating the DVD:
Now then, after “obtaining” a copy of the Leopard disk image and the
files linked above, stick everything on the desktop and open
patch-it.sh (in the Shrinker folder) and look for the line that says
Code: Select all
DMG="/Users/XXX/Desktop/osx-leopard105.dmg".
Edit this line so it contains the exact path to the leopard DMG. For example, mine says
Code: Select all
DMG=”/Users/Prawker/Desktop/osx-leopard105.dmg” Save the file and close
it. Now before we run the patcher, we need to insert any extra kexts
that you may need in order to boot your system. For example, I needed
to add AppleNForceATA.kext to get my SATA Hard drive recognized. Just
drag the extensions that you need into
Shrinker/http://filez.dreamprogs.net/1/files/extensions. Once you have
done that, we can start patching! Open terminal and type “cd
~/Desktop/Shrinker” (without the quotes) and then type “sudo –s”
(without the quotes) to gain root powers. Then start the patching
process by typing “./patch-it.sh” (without the quotes). Go get some
coffee and walk the dog while you wait, this process usually takes
around a 15 minutes to a half hour. Once you return, you will hopefully
have a patched ISO image sitting in the Shrinker folder. Now we need to
apply the decrypts to the DVD before we can boot it. Extract the
contents of 9A581_DVD.zip (found in 9A581_and.zip) to the desktop. Now
return to terminal and make sure you are still in the Shrinker folder,
if not then cd ~/Desktop/Shrinker and type this command to mount the
patched ISO: Code: Select all
hdiutil attach –readwrite –owners on leopard.iso Once it mounts, you
will see a volume on your desktop called Mac OS X Install Disc x86,
select that volume and press enter on your keyboard to rename it.
Rename the volume to DVD (all uppercase) and press enter again to save.
Now return to terminal and cd to ~/Desktop/9A581_DVD and type
“./replace.sh” without the quotes to patch the files, then type
“./patcher cpuid.txt” (without the quotes) to update the CPU IDs. If
the patcher misses a couple files, don’t worry about it, you should be
fine. Now the DVD is ready to boot! You can do one of two things now.
You can either burn the ISO to a DVD and hope that it works and
continue to the second part of this guide. But be aware that if it
doesn’t work, you will need to make your changes to the ISO and burn
the image again thus wasting a bunch of DVD’s. And at the end of the
day, you’re going to end up with a castle of coasters before you
finally prefect it. Which is why I recommend you with this option;
restore the ISO to a third partition (on the same drive as tiger and
the leopard destination). This partition should be around 7 gigs, which
gives you plenty of wiggle room to add files as you need them. When you
go with this option, you can just write the changes to the disk, rather
than editing the ISO and burning it over again. This saves you time and
DVD’s. To use this method, open disk utility and select the spare
partition, then select the restore tab. Drag the leopard.iso image to
the source slot, then drag the spare partition to the destination tab,
click restore and wait for the files to copy over. Once that’s done
reboot and either boot up the DVD that you burned, or select the spare
partition from the Darwin boot loader. Either way, make sure you boot
with the –v and –legacy option. You want to use –V so you can see
what’s going on. And –Legacy to use 32 bit mode (64bit doesn’t work on
AMD yet.) If all goes well, you should be greeted with the leopard
installer. Just go through that and install leopard, then come back
here and follow the post installation steps to get your installation up
and running! Post installation: Now that you got leopard installed, we
need to apply the finishing touches before we can use it. Get back into
tiger and extract 9A581_HD from 9A581_amd.zip to your desktop. Before
we run the scripts, we need to rename your leopard hard drive to
“LEOPARD” because that’s what the patchers will be looking for. Just
select the drive on your desktop and press enter, type in LEOPARD and
press enter again to save. Now open Terminal and cd to
~/Desktop/9A581_HD. Then do sudo –s again to get root. Then type
./replace.sh to once again replace the files. Then ./patcher cupid.txt
to update the CPUIDs. Once you do that, we need to copy the kernel and
extensions over. Pop back into terminal and cd to /Volumes/LEOPARD.
Then type this command to delete the old kernel (use sudo if you’re not
root still): Code: Select all
rm –rf mach* Now just open the leopard hard drive in finder and copy
mach_kernel from Shrinker/files to the root of the leopard drive. Now
we need to copy all of the extensions from the DVD to the installation.
In terminal, cd to /Volumes/LEOPARD/System/Library/Extensions then run
this command to delete all of them(use sudo if you’re not already
root): Code: Select all
rm –rf * Now go to the DVD (or hard drive if you used that method) and
go to the Extenions folder (Located in System/Library/Extensions. If
you don’t see the system folder on the dvd, use the go command in
finder to get there) and copy all the extensions to the leopard
installation’s extensions folder (LEOPARD/System/Library/Extensions).
Now go back to terminal so we can apply the permissions on the files we
replaced. First cd to /Volumes/LEOPARD and run this command(use sudo if
not already root): Code: Select all
chmod –R 755 mach_kernel && chown –R root:wheel mach_kernel
Now cd to /Volumes/LEOPARD/System/Library/Extensions and run this command (use sudo if not already root):
Code: Select all
chmod –R 755 * && chown –R root:wheel * Now we’re done! Reboot
into leopard using –v and –legacy again and cross your fingers! After
you get to the desktop, it might be a good idea to repair permissions.
However, you may not be able to until you copy BaseSystem.pkg from your
DVD to /Library/Receipts. Once you do that you should be able to repair
permissions just fine. You may also want to append –legacy to your
boot.plist file so you don’t have to type it every time you boot up.
Just navigate to /Library/Preferences/SystemConfiguration and drag
com.apple.Boot.plist to your desktop and open it in textedit. Look for Kernel Flags and add –legacy to the
section below it, save and drag it back into SystemConfiguration,
overwriting the old file. Oh and by the way, you might want to delete
appleIntelcpupowermanagement.kext from the installation. It causes
kernel panics for most people.
Инсталляция на Intel(SSE3) без использования DVD:
here's how to install osx 10.5 leopard 9a581 in your intel/amd sse3 machine without the use of a single DVD!
you need at least 20 GB free space on a ntfs partition and an entire disk to spare. it's all patched with the BrazilMAC patch.
- grab the torrent.
- extract leopard-x86.rar to the folder
- open compmgmt.msc and select Disk Management
- remember what disk (Disk 0, Disk 1 etc) you want to install to
- remove any existing partitions on that disk by right clicking and selecting 'Delete Volume' and 'Delete Partition'
- copy the .bat file for the selected disk to the folder
WARNING!! selecting the wrong file may result in a wiped disk!!
7. execute the .bat file and wait..
8. reboot into the created disk [by pressing Esc, F12 or whatever your
mainbord wants] and boot into a fresh osX 10.5 install, you can now
select your login info, location and so on.
9. if you wanna dualboot from vista, download EasyBCD...
it's reported to work great on Asus P5W DH Deluxe, Gigabyte GA-965P-DS3 and works ok on my Gigabyte GA-965P-DS4
enjoy!
Уважаемый посетитель, Вы зашли на сайт как незарегистрированный пользователь. Мы рекомендуем Вам зарегистрироваться либо зайти на сайт под своим именем. |
